• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window Pane Window Panes

A damaged or cracked window can be a source of frustration. It can also be a chance to upgrade your glass to energy-efficient or insulated windows to benefit from greater comfort, a higher potential for resales, and less bills.

This is a project you could do yourself for only a fraction of the cost of hiring an expert. You only need the right tools and a few minutes of your time.

Glass

If your single-pane windows are old, deteriorating or broken replacing them with modern insulated or tempered glass can increase energy efficiency and decrease noise while also preserving the original character of older homes. The majority of homeowners with basic hand tools can repair a window pane. You will also require an additional window pane, glazier's tips pliers, and latex glazing putty. If you need to you can use a heating gun to warm the old putty. Wear safety glasses and gloves prior to beginning. Working with broken glass could cause serious injuries.

Begin by removing any remaining broken pieces of glass. This is best accomplished with the help of pliers though using flathead screwdrivers can work in a pinch. Then, use a wood chisel or putty knife remove the rest of the old putty from around the frame and the sash. Be careful not to scratch the window sash. Take your time and work slowly. It is a good idea to work on a sturdy ladder rather than the ground and to have someone stand below the sash to help hold it in place.

Once you've removed all the old putty, replace window pane it is time to prepare the window frame to fit the new pane. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of the width and height. Bring these measurements to an hardware store or home center and get a piece of stock glass cut to size. Alternately, you can cut the glass yourself if have the appropriate tools.

After putting in the new glass Apply a small amount of caulking around the edge. This will make the glass weatherproof. Then, Replace Window Pane you can install a glazier's pointing on each side of the frame to secure the pane in its place. The points shouldn't be too tight that they create friction between the frame and sash but they shouldn't be too loose.

Before applying the putty to the surface, gently knead it until it is soft and free from lumps. Cut it into pencil-sized pieces. Place the first strip to the corner of the frame, working from one corner to another to ensure it is even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces of metal that help secure glass into a window frame without scratching or damaging the delicate surface. It's easy to learn how to use this nefarious tool and you can save money on the expense of a professional installation.

After the old putty and glazier's points are removed and the frame is thoroughly cleaned with a knife to eliminate any remaining traces. Lightly sand the wood in the rabbet grooves, if necessary, to smooth out rough areas. If you sand wood, protect it with painter’s tape to protect it from damage caused by accidental sanding.

Take the dimensions of the frame and write down accurate measurements. Take these dimensions to a hardware store or home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and will allow room for expansion and contraction.

Place the new window in the frame and press it into place firmly by using your hands. Utilize the point of the chisel, or the edge of the putty blade to smudge the glazier's points, as shown in Figure 11. When you're done taping, they should be flush with the top edge of the pane and the shoulders that are raised of the points should be just below the rabbet's rim groove.

Apply a thin bead of glazing compound over the edges of the new glass and in the rabbet grooves to seal and protect them. Let it dry and cure completely.

When the glazing compound is dry and the glazing compound is dry, you can install the new window replacement cost sash. The first step is to coat the wood with a heavy coat of linseed oil. This will stop the new putty drying out or cracking when it absorbs moisture. Apply this coat using a brush or the tip of your putty knife, then employ the chisel or back end of the putty knife to gently hammer in the new sash and glazier's point into the rabbet grooves. Repeat this procedure every 10 inches along the frame's perimeter.

Putty

A baseball hit or a rock thrown by error, or a fallen tree could result in a broken or cracked window. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in position by a small metal clip, also known as a glazier's point and putty. This compound is also referred to as glazing compound. Before you install a new pane, first remove the old one and clean up the area using the help of a rag, an abrasive scraper that is a pull type or a wood chisel. Wear safety glasses and gloves while working. You'll need a heat gun when the window is fixed into the frame.

If you're planning to reinstall your original sash, remove the molding that supports the old pane. Then you can sand the sash down to ensure it's level and ready for new caulk. Once the sash is installed, apply a new caulk made of silicone around the glass to ensure it will not leak or change color as time passes.

Take the glazing points out of the rabbets, the grooves in the sash, where the glass is. If they're hard to chisel, hold a hand tool such as a heating gun over them for a few minutes to soften them. When using a heated tool, be sure to not scratch the sash and its railings.

Create a bed for your new pane by removing the old glaze points and putty. Roll a piece of glazing compound between your hands, forming it to be about 1/2-inch thick. Then, push it into the rabbets in which the glass will rest. The glass must be positioned against the putty on both sides. If necessary, lightly tap your glass into the rabbet using your thumb.

If the new pane is cracked then you can seal it with a solvent-based glass glue or silicone caulk before pressing it into the sash. If the crack is not sealed, you'll require putty to keep water from getting in. Once the putty is dry remove the oily film from the glass and allow it to dry completely before you paint. Paint before the putty is completely dry. It won't make a strong seal and may be leaking or discoloring over time.

Paint

If you've had a broken window pane, you might be worried about the expense of replacing it. It's true that replacing a single pane glass doesn't have to be costly when you do it on your own. Even a double-paned window can be replaced at a fraction of the cost it costs a professional.

If you are working with a large glass window first, ensure that it is securely attached to the frame. This is relatively easy and fast using the right tools and techniques.

When you're ready to start taking off the old window pane by prying out the metal glazing points that are attached to it. These are small metal triangles which act as "nails" that hold the window within the frame. They are submerged beneath a bead or glazing glue which hardens into solid wedge that holds the wood frame securely in place and hides the sharp edges.

After you have the old pane removed clean the surrounding frame and wood. Scrape off any old paint and sand the rabbet grooves that the glazing points were. These should be sanded to the point of being bare, so that you can paint them the same color as the rest the frame. After sanding the wood then apply a layer of flax oil. This will help to prolong the life of the frame.

Then, take measurements of the dimensions of the window's opening. You'll need to take horizontal and vertical measurements of the entire opening and also the thickness of the old pane. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these dimensions to the hardware or home improvement store and ask them to cut you the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.