• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane (ivimall.com) Window Panes

A damaged window pane could be a source of frustration. This can be an opportunity to upgrade to energy-efficient windows or insulated ones to enjoy benefits such as improved comfort, higher resale value and reduced utility costs.

It's a project you can tackle yourself at only a fraction of the cost of hiring an expert. You'll only require the proper tools and a few minutes of your time.

Glass

Replace your old single-paned windows with tempered or insulate glass to improve energy efficiency, cut down on noise, and preserve the original character of your old home. The process of replacing a window pane is relatively simple and can be done by homeowners with basic hand tools. You will also require an extra window pane, glazier's tips pliers, and latex glazing putty. If needed you may use a heating gun to warm the old putty. Before starting, put on protective gloves and goggles since working with broken glass may cause injuries.

Begin by removing any broken pieces of glass. It is recommended to use pliers however, a flathead may be useful equally. Then, use a wooden chisel or putty knife to remove the remaining old putty from around the frame and the sash. Be careful and slow making sure not to break the current window sash. It is recommended to work on a sturdy ladder rather than the ground and to place someone on the sash in order to help hold it in place.

After you've removed all the old putty, prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Take these measurements to the nearest hardware store or home center, and replace window Pane get a piece of stock glass cut to size. Alternately, you can cut the glass yourself if you have the tools you need.

After installing the new pane, run a small bead of caulking around the edges to make it weatherproof. Then, place a glazier's tip on each side of the frame to secure the pane into the right place. The points should not be too tight that they cause friction between the frame and the sash However, they should not be loose.

Before applying the putty to the surface, gently knead it until it becomes soft and free of lumps. Then you can roll it into pencil-sized strips. The first strip should be placed in the corner of the frame, moving from one corner to another to ensure it is smooth and even.

Glazier's Points

The glazier's points are tiny triangular pieces of steel that allow glass to be secured into the window frame without damaging the delicate surface. It's simple to learn how to use this secret tool and you can save money on the expense of an expert installation.

After the old putty and the glazier's point are gone and the frame is thoroughly cleaned with a utility knife to remove any remaining residue. If necessary, lightly sand the wood along the grooves of the rabbet to smooth out rough areas. If you decide to sand the wood, make sure to protect it by using painter's tape to prevent accidental damage.

Note down the dimensions of the frame. These measurements can be brought to a home center or hardware store and the new pane will be cut to a smaller size. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane into the frame and push it into place firmly with your hand. Use the point of the chisel, or the edge of the putty blade to smudge the glazier's points as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane. the raised shoulders of the points should be just below the lip of the rabbet groove.

Apply a thin layer glazing compound on the rabbet grooves as well as the edges of new glass. This will protect and seal the edges. Allow it to dry and cure fully.

After the glazing compound dries and the glazing compound is dry, you can install the new window sash. First, you need to coat the wood with a thick layer of linseed. This will stop the new putty from drying out or cracking due to the moisture it absorbs. Apply the coat using a brush or the tip of your putty knife, then use the chisel, or the back end from the putty knife to gently press the new sash and glazier's point into the grooves of the rabbet. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown, a rock thrown in error, or a tree falling could result in a broken or cracked window pane. Fortunately, the majority of windows can be repaired by simply placing a new piece in the right place. The glass is held in place using a small metal clip called a glazier's point, and Replace Window Pane putty, often called glazing compound. Remove the old pane and clean the area with the rag, a scraper that is a pull type or a wood chisel. Wear protective glasses and gloves while doing this work. If the window is glued to the frame, you'll need to make use of a heat gun to soften the adhesive before cutting it loose.

If you are planning to replace the original sash, remove any molding pieces that secure the old pane. Then sand the sash to ensure it's smooth and ready for a new caulk. Once the sash is installed and sanded, apply a fresh caulk made of silicone around the glass to ensure that it doesn't swell or fade in time.

Remove the glazing points in the rabbets. These are the grooves on the sash, which is where the glass is located. If they are hard to cut, place an instrument such as a heating gun over them to soften first. If you're using a heat gun, be cautious not to damage the railings of the sash or the sash itself by placing the tool too tightly.

Make a bed for your new pane after you have removed the old putty and glazing points. Roll a rope with glazing compound between your fingers, and make it about 1/2 inch thick. Press it into the rabbets, where the glass will be placed. It's important that the glass sits on the putty on both sides So if you have to do so, gently tap the glass into the rabbet using your thumb.

If the new pane is damaged, you can use a silicone caulk or a glass glue based on solvents to seal the crack before pressing it in the sash. If the crack is not sealed, you'll need to use putty to keep the water out. After the putty has dried and the film is oily, wipe it off the glass with the help of a rag. Allow it to dry completely before painting. If you paint before the putty has completely dry, it won't form a solid seal and could discolor or leak in time.

Paint

You might be worried about replacing a broken piece of glass. It's true that replacing a single pane of glass doesn't need to be costly even if you do it your own. In fact even windows with double panes can be replaced at only a fraction of the cost of a professional.

If you're working with large glass windows first, ensure that it is securely attached to the frame. Using the proper tools and techniques to make this task relatively easy and fast.

When you're ready to start, begin by removing the old window by prying out the metal glazing points that are attached to it. These are essentially small metal triangles that act as "nails" that hold the window handle replacement in place in the wood frame. They are buried beneath a glaze putty or bead that sets to form solid wedge that holds the wood frame securely in place and hides the points.

After taking off the old pane clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. These should be sanded to bare wood to allow you to paint them the same shade as the rest of the frame. After sanding, apply a layer of flax oil to the bare wood to help extend its lifespan.

Next, measure the dimensions of the window opening. You will need to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you have the exact size for the new pane. This will also allow for expansion and contraction of the glass in times of seasonal change. Bring these measurements to the hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass window replacement and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.