• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They do not rot or rust like aluminum or timber.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will save you from unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is essential to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and the new window will usually fit inside the old frame very easily. If you have double-paned windows that are held together by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this situation you'll need to locate some plastic spacers that aid the new pane in being able to fit properly into the frame of the window.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass by yourself. You should also lay down a drop cloth before you begin working on the window panes, so that any shards of glass fall onto the fabric, not onto the floor and could be trampled.

Once the glass is removed from the window, it's best to seal the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional is able to come out and repair the window. It also acts as an obstruction to prevent criminals from getting into your home. If the gap is large, you may think about a security door that has an integrated window, as this will offer the best of both worlds.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash windows. However, over time, they are susceptible to a range of issues, including sliding. A window that is sagging can cause problems with light, draughts and even security. It's crucial to act immediately if you discover that your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window repair which is sliding. To do this, you'll have to open the window to get to the frame. Then, using the screwdriver, you'll be able to take off the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and check for fit. If you're happy with the fit, you can tighten the screws until they stay in position.

If you are unable to reposition the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, which causes them to loosen. It is crucial to replace your seal as quickly as you can in order to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also become loose. This is often caused by screws that have become undone over time, but it can also be due to the mechanism of the handle wearing out. Fortunately, it's easy to repair the handle of a window that is loose yourself. The first step is to close your window and do a test fit. The corners of the sash need to align with the casing joint. If it doesn't, you can use the screwdriver to loosen up the handle. Then, turn the mechanism to position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it is important that you take action. Water leaks through windows can cause structural damage to your home and also impact your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Based on the severity of the problem the caulking that was used up might need to be removed before a new layer is applied. It is important to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce the efficiency of your energy.

Check that any drainage holes are free of debris inside them and that the sill pan is properly angled to drain away from the window. In more serious cases you might need to consider replacing the window.

Mold spots and upvc window repair rotted sills are another sign of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass of your double glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be corrected by an uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or if it opens with an ease. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical part, hinges can wear out over time. It is essentially a very simple process, but it's simpler if you have someone to help hold the frame up.

Make sure that the uPVC hinges are closed and open in the proper direction. You can check this by looking for the arrows on each hinge. This shows which way the window should open.

The issue can be caused either by opening the window incorrectly or by a poor installation at the factory. This issue can be fixed by sending us a picture on our website. We will be more than happy to give you suggestions.

It is also essential to ensure that the hinges are lubricated regularly. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to operate and close more easily. It can also stop corrosion and reduce the possibility of sticking. The ideal time to do this at least once a year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts in upvc window repair windows can be caused by a variety of different things. Firstly the hinges, again because of wear and tear, may become displaced, which can cause gaps to develop where the sash joins the frame. If they are beyond repair, it could be necessary to have them realigned. The second is the interlock, which is located on the hinge side of the window, can also become misaligned, again it is possible to just give them a clean but in certain cases, it may be necessary to have them replaced.

These seals can wear down or be damaged over time, allowing air to escape. Installing high-quality weatherstripping will help to stop draughts. Another option is to replace the upvc window with low-emissivity glass. which will help regulate indoor temperatures and will lessen the possibility of draughts.

Lastly, one of the most effective methods to reduce draughts is by using a draught excluder. These are typically fabric tubes which are filled with a sort of filler and can be placed on the top of your windowsill. They will keep your home warm by blocking cold air.

With a bit of regular maintenance and repairs your windows made of upvc will provide an excellent level of insulation and security for your home. It is crucial to keep in mind that all windows eventually wear out and upvc window repair it may be more cost-effective to replace them than to repair them. So, if you are experiencing problems with your upvc Window repair windows, it is always best to seek professional assistance immediately.