• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can cause a lot of trouble. It could also be an opportunity to upgrade your glass to energy-efficient or insulated windows to benefit from more comfort, higher the value of resales and lower utility costs.

It's a project you can tackle yourself at a fraction of the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

Replace your old single-paned windows with tempered insulation glass to improve energy efficiency, reduce noise, and protect the historical integrity of your old home. The procedure of replacing windows is easy and can be completed by most homeowners who possess basic hand tools. In addition to a new pane, the following tools are required such as latex glazing putty; pliers, glazier's points and a heat gun for warming the old putty, if needed. Wear safety goggles and gloves before you begin. Working with broken glass could cause serious injuries.

Begin by removing any remaining broken pieces of glass. It is best to use pliers however, a flathead may work as well. Use a wood chisel, or putty knives, to take away any remaining old putty around the frame and Replacement Upvc Window Handles the window sash. Be careful not to break the window sash. Work slowly and carefully. It is best to work using a sturdy ladder instead of the ground and have someone stand below the sash to help hold it in place.

Once you have removed all the old putty, you can prepare the window frame to fit the new pane. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of the width and height. Bring these measurements to an hardware store or home center, and get a piece of stock glass cut to size. You can also cut the glass yourself if have the appropriate tools.

After installing the glass Apply caulking to the edge. This will make the glass weatherproof. Install a glazier’s point on both sides of the frame. This will ensure the pane. The points should not be tight enough to cause friction between the frame and sash, but they should also not be loose.

Before putting the putty on, knead it thoroughly until it is smooth and free of lumps. Make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to another, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of metal that allow glass to be secured to the frame without causing any damage to the fragile surface. Knowing how to use these tiny pieces of help is simple and could save you money on a professional installation or the cost of new glass.

After getting rid of the old putty glazier points as well as any remaining residue clean the frame thoroughly using a utility knife. If needed you can lightly sand the wood along the rabbet grooves to smooth out rough areas. If you sand wood protect it with painter's tape to protect it from damage caused by accidental sanding.

Note down the exact dimensions of the frame. These dimensions can be taken to an hardware or home centers store, and the new frame will be cut a bit smaller. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane in the frame and push it in using your hands. Then, you can use the point of your chisel or the back end of the putty knife to tap in the glazier's points as illustrated in Figure 11. The glazier's points should sit in line with the top edge of your pane and the raised shoulders should be just below the lip.

Apply a small amount of glazing compound on the edges of the glass that has been made and into the rabbet grooves to seal and protect them. Allow it to dry and cure completely.

Install the new window sash after the glazing compound has dried. First, coat the wood with a thick coat of linseed oil. This will prevent the new putty drying out or cracking when it absorbs moisture. Apply this coat using a brush or the edge of your putty knife, then use the chisel, or the back end of the putty knife to gently hammer in the new sash and glazier's points into the grooves of the rabbet. Repeat this procedure every 10 inches around the perimeter of the frame.

Putty

A baseball thrown at you, an errant rock or a falling branch can cause a window pane to break or crack. Fortunately, the majority of windows can be replaced by simply putting a new piece in the right place. The glass is held in place by a small metal clip called a glazier's point, and putty, which is often called glazing compound. Before installing a replacement window glass near me Upvc Window Handles (Www.Kmgosi.Co.Kr) pane, first get rid of the old one and clean up the area with the help of a rag, an abrasive scraper that is a pull type or a wood chisel. Wear gloves and safety glasses while you do this work. If the window is attached to the frame, you'll need to make use of a heat gun to soften the adhesive prior to cutting it loose.

If you are planning to install your original sash, you must remove the mold that holds the old pane. Sand Replacement Upvc Window Handles the sash until it's flat and ready to receive new caulk. Once the sash is re-installed, apply a new silicone caulk to the glass to ensure that it doesn't swell or fade as time passes.

Remove the glazing points from the rabbets. These are the grooves on the sash, where the glass is. If they're hard to chisel, use the hand tool, like a heat gun over them for a few minutes to soften them. If you're using a heated gun, be careful not to cause damage to the railings of the sash or the sash itself by placing the tool too close.

After the old glazing points and putty have been removed prepare a bed for the new pane. Roll a rope of glazing compound between your hands, and form it into a 1/2-inch thick. Press it into the rabbets, where the glass will be placed. It is essential that the glass sits on the putty in all places on both sides, so if you need to do so, gently tap the glass into the rabbet using your thumb.

If the new pane has cracked, you can use a silicone caulk or a glass glue based on solvents to fill in the crack prior to pressing it in the sash. If the crack is not sealed, you'll need to use putty to keep water from getting in. After the putty has dried remove the oily film off of the glass and let it dry completely before painting. If you paint before the putty is completely dry, it won't form a strong seal and may leak or discolor in time.

Paint

If you've had a broken window pane, you might be worried about the expense of a new one. However, replacing a single glass pane doesn't need to cost a fortune when you do it yourself. In fact windows with double panes can be replaced for less than the cost of an expert.

If you're working with a large glass window first, ensure that it is securely fixed to the frame. By using the correct tools and techniques you can make this task relatively easy and quick.

When you are ready to start taking down the old window pane. Remove the metal glazing points that are attached to it. These are tiny metal triangles which act as "nails", holding the window within the frame. They are submerged beneath a bead or glazing putty that hardens to an unbreakable wedge that holds the wood frame securely in place and hides the sharp edges.

After removing the old pane, clean the frame and wood. Scrape off any paint and sand down the rabbet grooves, where the glazing points were. Sand them down to bare wood surfaces, so that you can paint the frames the same color. After sanding, apply a coat of flax oil on the wood that is not sanded down to help extend its lifespan.

Then, you need to measure the width of the window's opening. You will need to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass during seasons of changes. Take these measurements to the hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.