• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they do not get rusty or decay.

Regularly cleaning and Repairs to uPVC Windows lubricating UPVC windows and doors is essential. This will save you from unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home and even be fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace and generally fit into frames that were previously in use very easily. If you have double-paned windows which are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this case you'll need locate some plastic spacers that will help the new pane to fit correctly into the window frame.

If you're planning attempt to remove the window panes by yourself it is important to wear appropriate safety gear that includes gloves with a thick layer of material and protective eyewear. It is also recommended to lay down a drop cloth prior to when you start working on the glass so that any shards fall on the fabric rather than on the floor where they could be trodden under and cause further damage.

It's a good idea to cover the gap with tape after the glass is removed. This will keep drafts and water from getting into your home until a professional is able to fix the window. It also acts as a barrier to prevent any criminals from getting into your home. If the gap is large, you might think about an alarm door that comes with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber sash windows. Over time, they can be affected by a variety of issues such as sliding. A sagging upvc window repair windows can cause problems with light, draughts and even security. It is crucial to act when you discover that your uPVC windows are sliding.

To fix a sagging window you can try to reposition the hinges. To do this, you'll need open the window to access the frame. With an screwdriver, unscrew the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have repositioned your hinges. If you're happy with the fit, you can tighten the screws to ensure that they remain in the right place.

If you are unable to move the hinges, you may have to replace the seal. Over time rubber seals can lose their elasticity and become dry, which causes their tightness to decrease. If this happens, it's important to replace the seal as fast as you can to ensure that your uPVC windows are waterproof and draught-proof.

uPVC handles can also become loose. This is usually due to screws that have been removed over time, but it can also be due to the handle mechanism wearing out. Fortunately, it's easy to repair the handle of a window that is loose yourself. First, you'll need close the window and perform an initial test fit. The corners of the sash should be aligned with the casing joint. If it isn't, you can use a screwdriver to loosen the handle, and then reverse the mechanism back into its original position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains it's important to take action. Water leaks from windows can not only cause destruction of your home's structure but also hinder your efforts to regulate the temperature in your home. Most often, upvc window repair near me window leaks are caused by a lack or repairs To upvc windows damage to the sealant.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on the severity of the problem the caulking that was used up might need to be removed before a fresh layer can be put on. When it comes to uPVC repair, it is important to be careful not to over-caulk. This will only make your window more difficult to clean and lower its energy efficiency.

Make sure that the drainage holes are free of debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more extreme cases, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. The mold thrives in damp environments and can quickly spread across the home.

If the leakage occurs between the double-glazed glass, it is more likely the issue is more with the seal rather than the frame. Again this can easily be fixed by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open, or if it opens in an ease. They can be easily replaced by any competent DIYer and can usually be done within a few minutes.

Like all mechanical parts hinges are prone to wear out over time. The process of replacing a hinge on a window is an easy process but it can be easier with someone else to help you hold the frame in place.

Make sure that the uPVC hinges are open and closed in the correct direction. You can do this by checking for the arrows on each hinge, this shows which way the window should be opened.

The problem can be caused by opening the window incorrectly or due to a poor installation in the factory. Sending us photos via our website is often enough to resolve the problem. We are happy to offer suggestions.

It is also crucial to grease the hinges regularly. Applying a light engineering lubricant to the hinges is a great method of doing this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. Ideally, you should perform this every year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a few different factors. The hinges can also become misaligned due to wear, causing gaps where the sash meets frame. These can be easily repaired by giving them a thorough clean, however if they are beyond repair it may be necessary to get them realigned or replaced. The interlock may also become misaligned. This happens on the hinge side and might require to be cleaned. In certain instances it might be necessary to replace them.

The next common reason for draughts are the window seals, these are susceptible to being worn out or damaged over time, and will allow air to escape through the gaps. Replacement of these with high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass, which will help regulate indoor temperatures and again will lessen the risk of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be hung over your window sill. They can help stop cold air from entering and keep your home warm and cosy!

Your upvc windows can keep providing excellent insulation and security in your home with regular maintenance and repairs. It is essential to remember that all windows eventually become worn out, and it could be more cost-effective to replace them instead of fixing them. If you have any problems with your upvc window, it's best to consult an expert as soon as possible.